About Ebykr
Ebykr celebrates classic and vintage lightweight bicycles through provocative imagery and opinion. Ride along with us.
About Ebykr
Ebykr celebrates classic and vintage lightweight bicycles through provocative imagery and opinion. Ride along with us.
Resources
How the gears, hubs and brakes of the classic lightweight bicycle work, drawn and set moving one step at a time. Every motion and every number comes from a patent, an instruction sheet or a catalog, in the Ebykr archive wherever it can be, and is cited beside the drawing. Where a detail is not in a document, the drawing says it is schematic.
Eleven mechanisms: eight are finished and three are roughed in, grouped by what they do. Each card names the documents it is drawn from. Point at a card, or tab to it, to see the mechanism at work.
Moving the chain from cog to cog. 4 finished, 2 roughed in.

Two links, a cable and a spring, fitted the way Campagnolo’s own sheet says: seven steps from the parts to a broken cable.

The light-alloy parallelogram fitted letter by letter from Huret’s sheet, with the chain it takes up worked out from the sheet’s own capacity.

A sprung arm and a toothed jockey sprocket, set by the folder’s rule that three pins line up in low gear.
Gap: the arm’s length and the spring’s rate are in no document read.

Two rods: one frees the wheel, one moves the chain and the wheel walks along the toothed dropouts.
Gap: Nos. 12 and 13 were read: they list the parts too, and none says how a rider works the two rods. That step rests on one speculative outside article.

The Gran Sport’s successor, drawn beside it: seven steps through what stayed and what changed between the two sheets.
A 1938 parallelogram worked by a two-ended cable on a crossbar, like an airplane rudder
: eight steps from the period review.
Gears inside the hub, and the lever that frees the wheel. 3 finished.

A fixed sun, four planets and a sliding clutch: eight steps from the parts to the leaflet’s own gear table.

The AW’s four-speed sibling: two suns and stepped planets, with its four ratios set against the AW’s three.

A handle, a rod and a wing nut clamp the wheel without a spanner: seven steps from Campagnolo’s own sheet.
bloccaggi originali
Two ways to pull two arms together. 1 finished, 1 roughed in.

A straddle wire lifts two arms on separate pivots, each with its own spring.
Gap: no arm lengths, so no leverage figure yet.

Two arms on brazed bosses and a straddle wire, with the catalog’s own brazing dimensions for four wheel sizes.
Measured on the archive’s documents table on 2026-11-16, 4,048 records. The AW came first because its leaflet prints the numbers that fix its motion. The Gran Sport and the Jubilee followed because each has the maker’s own fitting sheet with a drawing to work from.
| Candidate | Records naming it | Instruction sheets | The maker’s own documents | Numbers they print that fix the motion | Verdict |
|---|---|---|---|---|---|
| Sturmey-Archer AW | 57 | 0 | Leaflet AD 519 | Both ratios (+33.3%, −25%) and a 15-row gear table that agrees with them exactly | Built |
| Campagnolo Gran Sport | 97 | 1 | Catalog of about 1951 with parts 101 to 172; the fitting sheet of about 1960 with its drawing; a leaflet | None on the travel; the sheet’s drawing and five fitting steps | Built |
| Huret Jubilee | 24 | 1 | The fitting sheet, in three languages, with lettered drawings | Capacity 13 to 24 and 36 to 53, which fixes the chain the cage takes up; 3 mm and 10 mm settings | Built |
| Cyclo Benelux | 81 | 0 | Benelux folder with fitting instructions and a drawing; a conversion leaflet | None on the mechanism; the pin-alignment rule | Roughed in |
| Mafac centerpull | 61 | 0 | Catalog of the 1950s with the Racer in parts; catalog of 1976 | Fitting sizes only: 6 or 7 mm pivot bolts | Roughed in |
| Cambio Corsa, Paris-Roubaix | 6 | 0 | Catalog of about 1951 with both gears in numbered parts; Nos. 12 and 13 | None | Roughed in |
| Campagnolo quick release | 278 | 1 | Quick release hubs instructions of about 1960; the 1951 catalog | Parts 2 to 61 and three fitting rules; no dimensions | Built |
| Nivex | 5 | 0 | None; a 1938 review | Gear range and development, 2.30 to 7.80 m | Built |
| Simplex plunger | 76 | 0 | None found; the Simplex sheets held are for later parallelograms | Not yet known | Set aside |
Records naming it: documents whose transcription or title names the mechanism, read from the archive’s documents index on 2026-11-16; most are dealer catalogs and advertisements that only list it. Instruction sheets: the archive’s instructions type. The Simplex plunger has no reliable count yet: a text search mostly finds the name of Lucien Juy, and the trade-press surveys of 1951 to 1954 that may describe the plunger gears are still to be read.
Each needs a document that shows how it works before it can join the set. Counts are archive records naming it (a loose text count, 2026-11-16).
Motion and numbers come from a patent, an instruction sheet or a catalog. Web pages that agree with one another count as one source.
exact printed in a document; derived follows from one; schematic drawn to explain, not measured.
Neutral ink in the weight of the site’s icons. Gray hatching tells one moving group from the next, the way a drafting section does, and dense gray marks what is held still. One blue, and only blue, marks whatever carries the load. A switch on every drawing offers colors or plain lines instead. No period-plate imitation.
With reduced motion set, each step is a still. Every control works from the keyboard.
The Ebykr Digest
New articles, timelines, catalog finds and registry activity — assembled from the archive once a month. Your address is never shared.
Double opt-in. One email per month. Unsubscribe at any time with one click.