Repair Workshop Wheels and tires Wired-on tire puncture

Repair · Wheels and tires

Mend a Puncture in a Wired-On Tire

How two handbooks of 1913 and 1916 mended a puncture in an ordinary tire, a cover with a wired or beaded edge over a separate inner tube: the valve tested first, the cover lifted off, the leak found by feel or in water, the patch put on only when the solution had gone tacky, and the cover put back with its beading checked. Every instruction is from the Ebykr archive; the drawings are Ebykr’s own.

DifficultyEasyPatience with the solution (Ebykr’s estimate)
StepsSevenFrom Henry, 1913, and Cassell, 1916
You will needSeven tools, five materialsThe list, in the sources’ terms
SourceHenry 1913 and Cassell 1916Records 94435 and 94257

Before you start

This page shows how period sources mended a punctured tube, step by step, in their own words and figures. It does not test or guarantee any repair. A tire is a safety part: Henry warns that a bead not seated in the rim can burst the tube when the tire is pumped up, and Cassell that most failed patches fail because the solution was not given time. The petrol and benzine these sources use as solvents are flammable, so keep any flame away. If you are not sure of the repair, ask a bicycle shop to check it before you ride.

On this page The drawing Tools and parts The steps in words What goes wrong Another way Sources

Escape also leaves this view.
    Drawing key
    Workbench view: one step at a time in large type, for a phone or tablet on the bench.

    Tools and parts

    In the sources’ own terms; every item is named in them. Tick each one off as you gather it.

    Tools

    • Tire levers Only if the fingers cannot lift a wired cover (Henry)
    • An indelible pencil To mark the cover and the puncture (Henry, Cassell)
    • A bowl or pail of water To find the leak (Henry, Cassell)
    • An eggcup For the valve test (Henry)
    • Glass paper An abrasive paper; or the moistened head of a match, for the sulfur (Henry)
    • A pocket-knife For a flint that sits deep in the cover (Henry)
    • Two pennies and a screw-hammer Optional, to hold a patch while it sticks (Henry)

    Henry also names a pump and the lamp to be taken off; neither is a tool for the job itself.

    Parts and materials

    • Rubber solution Good solution, from the outfit box (Henry, Cassell)
    • Patches Round rubber patches from an outfit, or cut from an old tube (Henry, Cassell)
    • French chalk For the tube, and for the inside of the cover (Henry)
    • Petrol Gasoline, to clean the tube and the patch (Cassell)
    • Valve rubber and a piece of soap Only if the valve tests bad (Henry)

    The steps in words

    The whole job, readable and printable without the drawing. Each step says what it rests on, and can take you back up to its drawing.

    Test the valve first

    Before you look for a puncture, test the valve: Henry says the valve rubber perishing is often the cause of a leaking tire, and that it should be tested before the cover is taken off. Pump the tire up very hard, half fill an eggcup with water and stand the valve in it. If small bubbles come up from the valve, it wants new rubber. Unscrew the body nut, take out the stem, strip off the old rubber and rub the stem with soap, which lets the new piece slip on without trouble, then put the body nut back and screw it up tight with the fingers. Cassell says a valve can leak in three places: where it is fitted to the tube, between the main part and the removable piece, and at the point of the valve with the cap off. The first means the nut is not tight enough or the head has cut into the tube; the other two mean a perished or torn rubber, cured by a new one or sometimes by turning the old one round.

    What this step rests on
    • exact The valve rubber often perishing, the valve tested before the cover is removed: the tire pumped very hard and the valve put in an eggcup half full of water, bubbles meaning new rubber; the body nut off, the stem out, the old rubber off, the stem rubbed with soap and the new rubber slipped on, the body nut screwed tight with the fingers: Henry 1913, pages 58 and 59.
    • exact A valve leaking at three places; the nut tightened or, if the head has cut into the tube, the valve fitted in a fresh place and a patch over the old hole; the other two places from a perished or torn valve rubber, mended with a new rubber or sometimes by reversing the old one: Cassell 1916, pages 58 and 59.
    • exact The valve nut working loose as the cause of a puzzling leakage: Henry 1913, page 64.
    • not stated Valves other than the Dunlop pattern (Henry) and the Woods pattern (Cassell).

    Look for flints and mark the cover

    If the valve is sound, hold the machine so that the wheel turns clear of the ground and look over the cover for flints. A flint may be so deep that only a pocket-knife will get it out. Mark the cover with an indelible pencil where the trouble is, or count how many spokes it is from the valve, so that you can find the same place on the tube. Then take off the lamp and turn the machine upside down so that it rests on the saddle and handlebars. For a back tire, place the machine so that the cover can come off on the side opposite the chain wheel.

    What this step rests on
    • exact The machine held so that the wheel revolves clear of the ground to look for flints, a flint too deep to come out without a pocket-knife; the cover marked with an indelible pencil or the spokes counted from the valve; the lamp taken off and the machine turned upside down on its saddle and handlebars; for a back tire, the cover removed on the side opposite the chain wheel: Henry 1913, pages 59 and 60.
    • not stated Cassell does not describe this step, and neither book says how to take the wheel out of the frame: Henry mends the tire with the wheel still in the machine.

    Take the cover off

    For a beaded cover, take out the valve plug and unscrew the bottom milled nut, push the narrow beaded edge into the bed of the rim, put your fingers underneath and lift the cover over the edge of the rim. The tube is then bare and comes out easily. For a wired cover, let the air out, press the cover into the bed of the rim opposite the valve with your fingers and slide them gradually toward the valve. The cover loops up above the rim at the valve: slip your fingers under the loop, lift the cover over the edge of the rim and slide your fingers round. If your fingers cannot do it, use a pair of tire levers: put both under the wire about 6 in. apart and pull downward, then take hold of the part of the cover that is free of the rim and pull it toward the hub. Take care with the levers, since careless use tears the tube.

    What this step rests on
    • exact A beaded cover: the valve plug out, the bottom milled nut off, the narrow beaded edge pushed into the bed of the rim, the fingers underneath, the cover lifted over the edge; a wired cover: the tube deflated, the cover pressed into the bed of the rim opposite the valve, the fingers slid toward the valve, the loop at the valve lifted over the rim; two levers put under the wire about 6 in. apart and pulled down, the freed part pulled toward the hub; careless levering tearing the tube: Henry 1913, pages 59 and 60.
    • not stated Cassell says nothing about taking a cover off, so this step rests on Henry alone. Henry names a make of lever but does not describe one.

    Find the puncture

    Pump the tube up lightly until it takes a round shape. Look first at the place where the cover was marked. If the trouble is not there, feel round the inside of the cover for any sharp flint that comes through. If that finds nothing, either hold the tube close to your face and stretch it in short lengths until you feel the air escape, or put it in water until a stream of bubbles shows the place. Cassell does the water test 6 to 8 in. at a time in a bowl or pail, stretching the tube slightly while it is under, and going carefully round. Mark the place with an indelible pencil. Cassell adds that a net bag was sold for the tube while it was tested, so that it could be pumped up much harder and very small punctures were easier to find. Henry says a tube that leaks and will not show it under water is more bother than it is worth: a self-sealing solution may be tried, but a new tube is better.

    What this step rests on
    • exact The tube lightly inflated to a round shape, the marked place examined first, the inside of the cover felt for flints, the tube held near the face and stretched in short lengths or put in water until a stream of bubbles shows the place, the spot marked with an indelible pencil: Henry 1913, pages 59 and 60.
    • exact The tube slightly inflated and put in a bowl or pail of water 6 to 8 in. at a time, slightly stretched while under, the bubbles followed round and the puncture marked; a net bag, about a shilling, letting the tube be pumped up much harder: Cassell 1916, page 54.
    • exact A tube that leaks but will not show it in water, a self-sealing solution to try, a new tube better: Henry 1913, page 62.

    Clean, put on solution and wait until it is tacky

    Take the gray sulfur coating off the tube round the puncture with glass paper or, Henry says, the moistened head of a match. Cassell wants more than glass paper, which leaves the sulfur and chalk only rubbed off: clean the tube thoroughly with petrol (gasoline) before putting on two coats of solution, and do the same to the patch. Henry puts one coat of good rubber solution round the puncture and one on the patch and sets both aside for about 10 minutes to get tacky. Cassell says there is no hard and fast time, since some makes take longer than others, and that 90 percent of failures come from not allowing enough: 10 or even 20 minutes may be given with advantage. Cassell adds that a roadside job should not be hurried, because it may have to be done all over again before many miles are covered.

    What this step rests on
    • exact The gray coating of sulfur removed with glass paper or the moistened head of a match, a coat of good rubber solution round the puncture and on the patch, both laid aside for about ten minutes to get tacky: Henry 1913, pages 60 and 61.
    • exact The tube cleaned with petrol, not glass paper only, before two coats of solution, and the patch the same; time given for the solution to get tacky, 90 percent of failures from not giving enough, 10 or 20 minutes allowed; a roadside repair not hurried: Cassell 1916, pages 54 and 55.
    • not stated The two books differ on the coats (Henry one, Cassell two) and on the wait (Henry about 10 minutes, Cassell 10 or 20); the page gives both.

    Press the patch down and powder the tube

    When both are tacky, lay the patch over the puncture and press well together. To save time when there is more than one puncture, Henry holds each patch down with a penny on it and another on the other side of the tube, gripped together with a screw-hammer, so that the next repair can be done while the first sticks. Sprinkle the tube freely with French chalk so that it does not stick to the inside of the cover when it is pumped up, and see that the tube is quite dry before it goes back in the cover: a dry tube goes in much more easily, and a damp one would rot the fabric. Henry says the inside of the cover should be chalked too.

    What this step rests on
    • exact The patch placed over the puncture and pressed well together; a penny on the patch and one on the other side of the tube, gripped with a screw-hammer, while the next repair is done; the tube sprinkled freely with French chalk, and made sure not to be damp, as a dry tube goes in much easier and will not rot the fabric: Henry 1913, pages 61 and 62.
    • exact The inside of the cover sprinkled freely with French chalk before the tube goes in, or the tube sticks to it the next time the cover is off: Henry 1913, page 70.
    • derived Henry’s screw-hammer is read here as the adjustable wrench that Fig. 36 of Henry’s book shows.
    • not stated How long a patch should be left before the tube is pumped up: neither book says.

    Put the tube and cover back and pump it up

    For a beaded cover, make sure the valve hole in the beaded edge is exactly over the hole in the rim, put the valve through it and slip the tube under the cover. See that the tube is not stretched or bulged anywhere. Press the beaded edge over and under the inturned edge of the rim; if the beading is stiff, bang the cover with the palm of your hand. A wired cover goes back the same way: slip the wired edge over the rim with your fingers as far as it will go, then press both thumbs in between the cover and the rim opposite the wired edge still outside and slide them in opposite directions round the rim, pressing as you go, until the rest sits in the bed of the rim. With levers, go as far as you can with your fingers, put two levers under the wired edge, taking care not to nip the tube, and pull upward. When you pump the tire up, glance round the rim to make sure the beading is still seated, or a nasty burst in the tube may follow. Henry tests the pressure by grasping the rim and pressing with both thumbs: if only a slight impression can be made, the tire is fit to ride. With a gauge, 25 to 30 lb. to the square inch gave good results on the tires of Henry’s day, the front a little less hard than the back.

    What this step rests on
    • exact A beaded cover: the valve hole in the beading over the hole in the rim, the valve through it, the tube slipped under the cover and not stretched or bulged, the beaded edge pressed over and under the inturned edge of the rim, a stiff bead banged with the palm; a wired cover: the wire slipped on with the fingers, both thumbs pressed in between cover and rim opposite the wire still out and slid in opposite directions, or two levers under the wired edge, the tube not nipped, pulled upward; the beading checked all round when pumping up, or the tube may burst: Henry 1913, pages 61 and 62.
    • exact The thumb test, a slight impression meaning the tire is fit to ride; 25 to 30 lb. to the square inch by a gauge for good results; the front tire not quite so hard as the back; the rider’s weight just bulging the tires where they touch the road; less hard on greasy roads: Henry 1913, page 56.
    • not stated Cassell does not describe putting a cover back, so this step rests on Henry alone. Henry’s figure is for the tires of 1913; this page does not offer it for any other tire.

    What goes wrong

    Each of these is a source’s own warning, except the last, which is what the sources leave out.

    • A tube torn by a lever Careless use of tire levers tears the tube; take care that it is not nipped under the wired edge (Henry).
    • A patch put on too soon Cassell says 90 percent of failures come from not giving the solution time to get tacky.
    • A tube cleaned with glass paper only Rubbing off the sulfur and chalk is not enough: clean with petrol before the solution (Cassell).
    • A damp tube It goes back much less easily, and a wet tube rots the fabric of the cover (Henry).
    • A bead not seated When pumping up, glance round the rim: a beading not securely embedded may burst the tube (Henry).
    • A tire ridden nearly flat A jerk over a stone makes the rim touch the road and nip the tire (Henry).
    • A leak that will not show in water Henry says such a tube is more bother than it is worth, and a new one better than a self-sealing solution.

    Wheel out, wheel in and how long to wait Neither handbook says how to take the wheel out of the frame or put it back: Henry mends the tire with the wheel in the machine. Neither says how long to leave a patch before the tire is pumped up. The one pressure, Henry’s 25 to 30 lb., is for the tires of 1913.

    Related jobs

    A burst in the tube

    Henry says a large gash or burst is much harder than a puncture, because a plain patch will generally be found to lift and leak after a time. Henry cleans the tube and the edges of the burst with special care, cuts a patch about 1 in. longer than the burst, rolls it up and puts it inside the tube, then solutions it, and puts a second patch of the same size on the outside, each cleaned and solutioned and pressed together when tacky. To keep the edges from curling back Henry holds the tube between two pieces of wood about 2 in. wide with a screw-hammer, as in Fig. 36. Henry 1913, pages 62 and 63.

    A valve that has cut the tube, or punctures round the valve

    Both books move the valve to a better place and mend the old hole with a large patch; Henry loosens the old seating and patches with a little benzine. Henry cuts a hole about an eighth of an inch across in the middle of an oval patch about 3 in. by 2 in. and in the tube, solutions the patch, wets the valve and pushes it through, and screws the washer and nut tight. Cassell cuts a hole about 3/16 in. across in a diamond-shaped patch about 2½ in. by 1¼ in. and in the tube, and solutions a piece of thin linen over the patch before the washer and nut. The sizes differ, so this page gives neither as a step. Henry 1913, pages 63 and 64; Cassell 1916, page 55.

    A leaky joint in the tube

    Cassell says not to mend a joint with a patch, because the air escapes along the edge under it: undo about three parts of the joint, roll it back, clean and put solution on both surfaces and bring them together again. If the joint must come wholly apart, a little petrol dissolves the old cement; Henry does it with benzine, turns one end back about 4 in. over a cylinder such as a piece of broom handle, draws the other end over it and joins it with solution. Cassell 1916, pages 55 and 56; Henry 1913, pages 64 and 65.

    The cover itself

    Cassell calls surface cuts in the tread the beginning of nearly all cover troubles, to be looked for and attended to at once: the cut cleaned and filled with a stopping, a deep cut that has hurt the fabric patched inside with proofed canvas first, and a burst patched with fabric wide enough to lap round the beads or wires. Cassell says any cover repair other than the smallest should wait at least a day before the machine is used. Henry also fills cuts with a stopping and patches the canvas from inside. This page does not give either as steps. Cassell 1916, pages 45 to 49; Henry 1913, pages 65 to 67.

    Sources

    Every record opens in the Ebykr archive. Each step above names the page it rests on.

    Record 94435, pages 56 to 66Peter Henry, Cycle Building and Repairing, 1913Chapter V on tire repairing: the valve tested, a beaded or wired cover taken off and put back, the leak found and patched, and how hard to pump.
    Record 94257, pages 44 and 54 to 59Cassell, Cycle Repairing and Adjusting, 1916 reprintThe tube tested in water, a patch cleaned and given time to get tacky, a valve moved, a joint mended and a leaky valve cured.

    Henry’s book is the Library of Congress copy on the Internet Archive; Cassell’s is DTU Library’s copy (Danmarks Tekniske Kulturarv). Both are public domain, and the archive carries their page images in full with Ebykr’s own reading of the print. The two agree on finding the leak and on giving the solution time, and differ on how much cleaning the tube wants and how long to wait. Henry alone takes the cover off and puts it back. This page puts the sources in Ebykr’s own words and quotes nothing at length.

    Exact, derived and schematic

    • exactThe valve test, the new rubber and the tight nut; the flint and the mark on the cover; the cover off by fingers or by levers; the leak found by feel or in water; the sulfur removed, the petrol, the solution and the 10 or 20 minutes; the patch pressed, the French chalk and the dry tube; the cover put back and the beading checked; Henry’s thumb test and 25 to 30 lb.
    • schematicThe drawings: the wheel, the cover, the tube, the bowl, the levers, the patch and the pennies, the number of spokes drawn and all motion. Ebykr’s own drawings.
    • not statedHow to take the wheel out and put it back, how long to leave a patch, a pressure for any tire after 1913, and every valve but the Dunlop and Woods patterns.

    The Ebykr Digest

    A monthly letter on classic lightweight bicycles

    New articles, timelines, catalog finds and registry activity — assembled from the archive once a month. Your address is never shared.

    Double opt-in. One email per month. Unsubscribe at any time with one click.